7-25
The lamp lights ON when the oil pressure of service brake drops
below the normal range.
When the lamp is ON, stop the engine and check for its cause.
Do not operate until any problems are corrected.Do not operate until any problems are corrected.
①
②
※
This lamp is ON when key ON, it is turned OFF after starting the
engine.
Check the battery charging circuit when this lamp comes ON,
during engine operation.
①
②
77073CD16
77073CD22
PrimaryPrimary
This lamp indicates that the primary steering has failed. When
the indicator comes on and the action alarm sounds, steer the
machine immediately to a convenient location and stop the
machine. Stop the engine and investigate the cause.
Do not operate the machine until the cause has been cor-Do not operate the machine until the cause has been cor-
rected.rected.
EmergencyEmergency
This lamp indicates the emergency steering system is active.
Immediately pull the machine to a convenient stop and stop Immediately pull the machine to a convenient stop and stop
the engine.the engine.
The emergency steering system can be manually tested. The emergency steering system can be manually tested.
Refer to page 7-47.Refer to page 7-47.
①
※
②
※
※
77073CD66
77073CD15
Steering warning lampSteering warning lamp
(9)(9)
Battery charging warning lampBattery charging warning lamp
(10)(10)
Brake fail warning lampBrake fail warning lamp
(11)(11)
7-26
PILOT LAMPSPILOT LAMPS
4)4)
Warming up pilot lamp
Mirror defrost pilot lamp
Preheater pilot lamp
Maintenance pilot lamp
FNR select pilot lamp
Clutch cut off pilot lamp
Ride control pilot lamp(Auto)
Ride control pilot lamp(On)
Seat belt pilot lamp
High beam pilot lamp
Parking brake pilot lamp
Joystick steering pilot lamp
Fan reverse pilot lamp
75793CD10
This lamp is turned ON when the coolant temperature is below
30
˚
C (86
˚
F).
The automatic warming up is cancelled when the engine coolant
temperature is above 30
˚
C, or when 10 minutes have passed
since starting the engine.
①
②
75793CD31
Warming up pilot lampWarming up pilot lamp
(1)(1)
This lamp lights ON for the first five seconds after starting the
engine.
①
75793CD17
Seat belt pilot lampSeat belt pilot lamp
(2)(2)
This lamp comes ON when mirror defrost switch is pressed.
①
7807A3CD11
Mirror defrost pilot lampMirror defrost pilot lamp
(3)(3)
7-27
This lamp works when the illuminating direction is upward.
This lamp comes ON when the dimmer switch is operated, e.g.,
when passing another vehicle.
①
②
When the parking brake is actuated, the lamp lights ON.
Check the lamp is OFF before driving.Check the lamp is OFF before driving.
①
※
77073CD12
77073CD13
This lamp lights ON when start switch is turned clockwise to the
ON position. Light will turn off after approximately 5~45 sec-
onds, depending on engine temperature, indicating that preheat-
ing is completed.
When the lamp goes out the operator should start cranking the
engine.
①
②
77073CD14
This lamp will be ON when the consuming parts are needed
to change or replace. It means that the change or replace-
ment interval of the consuming parts remains below 30
hours.
Check the message in maintenance information of the moni-
tor menu. Also, this lamp lights ON for 3 minutes when the
start switch is ON position.
①
②
75793CD32
High beam pilot lampHigh beam pilot lamp
(4)(4)
Preheat pilot lampPreheat pilot lamp
(5)(5)
Parking brake pilot lampParking brake pilot lamp
(6)(6)
Maintenance pilot lampMaintenance pilot lamp
(7)(7)
This lamp lights ON when the clutch cut off mode switch is
positioned L, M, H.
ReferRefer to page 7-48. to page 7-48.
①
※
77073CD65
Clutch cut off pilot lampClutch cut off pilot lamp
(8)(8)
7-28
The lamp comes ON when FNR select button on the optional
FNR remote control lever is pressed.
①
7807A3CD24
This lamp lights ON when joystick steering is activated.
It is then possible to steer the machine and select gears from the
armrest to the left of the operator's seat.
①
77073CD41
Auto ride controlAuto ride control
This lamp lights ON when push in the bottom of the ride control
switch (auto position).
Refer to page 7-47.Refer to page 7-47.
①
※
75793CD33
FNR select pilot lampFNR select pilot lamp (option)
(9)(9)
Joystick steering pilot lampJoystick steering pilot lamp (option)
(10)(10)
Ride control pilot lampRide control pilot lamp (option)
(11)(11)
This lamp lights ON when the fan control switch is pressed.
Refer to page 7-46.Refer to page 7-46.
①
※
7707A3CD40
Fan reverse pilot lampFan reverse pilot lamp
(12)(12)
Manual ride controlManual ride control
This lamp lights ON when push in the top of the ride control
switch (manual position)
Refer to page 7-47.Refer to page 7-47.
②
※
75793CD34
7-29
LCDLCD
5)5)
1
2
3
2
Type 1
The LCD can be used with the gear selector.
It indicates speed and driving direction.
(1)
75793CD39
No Symbol Meaning Remark
1 Actual gear display
Forward, reverse, neutral
1, 2, 3, 4 Actual gear
P Parking brake mode active
2 Forward, reverse Automatic mode
3 Gear range display Automatic mode
,
7-30
Camera / ESC button
Enter button
Menu button
Left move button
Right move /
buzzer stop button
Main display
Vertical
Horizontal
75793CD23
Main display to main menu, main menu to main display.
AEB cancel button in AEB setting.
①
②
75793CD90
BUTTONSBUTTONS
Menu buttonMenu button
1)1)
Move in menu (left, up).
①
75793CD91
Left move buttonLeft move button
(2)(2)
Enter rear camera mode in main display.
Cancel button except in main display (move previous menu).
①
②
75793CD92
Camera / ESC buttonCamera / ESC button
(3)(3)
Select menu (enter).
AEB cancel button in AEB setting.
①
②
75793CD94
Enter buttonEnter button
(5)(5)
Move in menu (right, down).
Buzzer stop.
①
②
75793CD93
Right moveRight move
/
Buzzer stop buttonBuzzer stop button
(4)(4)
(1)(1)
2. 2. MONITORMONITOR
·
The monitor is adjustable.
- Vertical : 14
˚
- Horizontal : 30
˚
7-31
MAIN MENUMAIN MENU
2)2)
1
2
6
3
7
10
4
5
8
9
8
9
10
5
6
7
TYPE A (default)
TYPE B
Main display
Main menu
Press
75793CD11
StructureStructure
(1)(1)
1 Buzzer
2 Clock
3 Wiper speed
4 Actual gear
9 Hour meter, odometer
10 Monitoring
Display type can be changed by operator. See page 7-42.Display type can be changed by operator. See page 7-42.
※
5 Select gear
6 Engine mode
7 Transmission mode
8 Engine rpm
No Main menu Sub menu Description
1
MODE
Engine setting
Kick down setting
Wiper speed setting
Fan-auto mode
AEB setting
Speed meter setting
Sensor calibration
Engine warming up, Engine speed
Mode 1 (down/up), Mode 2 (down only)
4 steps
Interval and time setting
AEB setting
Pulse setting
Boom/bucket angle, Boom pressure calibration
2
MONITORING
Fault code
Machine monitoring
Record monitoring
Machine, TCU, ECU, SCU
Hyd temp, Battery, Coolant temp
T/M oil temp, Weighing system
Hour meter, ODO meter
3
MANAGEMENT
Machine security
Maintenance
Machine information
Service contact
Service
ESL system setting, Change password
Replacement, Change interval (oils and filters)
Version, Status
Service contact
S/W download
4
DISPLAY SET UP
Clock
Display setting
Unit setting
Rear camera setting
Language setting
Clock
Brightness setting (Manual/Automatic)
Type display (A or B type)
Temp (
˚
F/
˚
C), Distance (
km/mile
), Pressure (
bar, Mpa, kgf/m
2
, psi
)
Reverse mode, Active camera, Display order
12 languages
75793CD12
75793CD13
75793CD14
75793CD13
7-32
ModeMode
Engine settingEngine setting
(2)(2)
①
75793CD16
75793CD16A
75793CD16B
75793CD16C
75793CD16D
Kick down settingKick down setting
②
Mode 1 (down/up)
:
Press kick down button once, shift down and press button again, shift up.
Mode 2 (down only) : Press kick down button every time, shift to lower gear respectively.
Refer to page 7-50.Refer to page 7-50.
75793CD17
75793CD17A
·
·
※
Wiper speed settingWiper speed setting
③
75793CD18
75793CD18A
Setting wipe speed 1 to 4.
·
Set low idling speed
Fan-auto modeFan-auto mode
④
75793CD110
75793CD111
75793CD112
Select reverse interval or reverse time.
Set reverse interval (30~300 min) or reverse time (30~300 sec).
Default : Interval (60 min), time (120 sec)
Refer to page 7-46, fan control switch.
·
·
※
※
7-33
AEB settingAEB setting
⑤
Actual gear window
75793CD19
75793CD19A
AEB mode controls the disk clearance of the transmission, automatically.
To start AEB setting, press and hold for 3 seconds.
To cancel AEB setting, press , or .
If "OK" in actual gear window, press , or to complete AEB setting.
Display during AEB modeDisplay during AEB mode
·
·
·
·
·
Symbol Meaning
ST Start AEB
K1~K4, KV, KR Calibrating clutch K1~K4, KV or KR respectively
OK
*
Calibration for all clutches fi nished
Spanner and Kx
*
Kx couldn't be calibrated, AEB fi nished
△
E
Engine speed too low
- Raise engine speed
▽
E
Engine speed too high
- Lower engine speed
△
T
Transmission oil temperature too low
- Heat up transmission
▽
T
Transmission oil temperature too high
- Cool down transmission
FO
*
Output speed not zero
FN
*
Shift lever not in neutral position
FP
*
Parking brake not applied
: : Transmission stays in neutral, you have to restart the TCU (ignition off/on).
*
Speed meter settingSpeed meter setting
⑥
75793CD20
75793CD20B
75793CD20A
Press and hold for 3 seconds.
To change the pulse value, press or .
To change the position, press .
Only for the serviceperson.
·
·
·
※
7-34
Sensor calibrationSensor calibration
⑦
75793CD21
75793CD21A
75793CD21B
75793CD21C
75793CD21D
Boom / Bucket angle calibrationBoom / Bucket angle calibration
CPU get sensing signal from boom link angle
and bell crank angle and calculate bucket
cylinder stroke and boom link position angle
from ground real time basis.
Boom link angle position and bucket cylinder
stroke is set by boom kickout & bucket leveler
set switch in cab.
Individual setting position is done by lever
solenoid (detent, release operation).
Angle sensor calibration is basically carried out
before delivery of the machine.
When angle sensor is replaced or actual value
is different compared to setting value, this
function can be done.
Boom link angle
Bucket cylinder stroke
Bell crank angle
Boom kickout & bucket
leveler set switch
75793CD128
The calibration must be carried out as follows :
Lower the boom at maximum low position and select (bucket must be max tilting position).
Raise boom at maximum high position and select .
Position boom at -5˚ and select .
Retract bucket cylinder length (to minimum position) at -5˚ boom position and select .
Extend bucket cylinder length (to maximum position) at -5˚ boom position and select .
In case above steps are carried normally, "complete" message is shown. Then angle sensor
calibration is finished after selecting .
·
-
-
-
-
-
①
②
③
④
⑤
⑥
display A
Không có nhận xét nào:
Đăng nhận xét